Electrician Tools

True-RMS multimeter with non-contact voltage detection, built for daily commercial/residential electrical work.

Covers the basics (voltage, resistance, continuity) at a fraction of the cost of a professional-grade meter.

Auto-ranging clamp meter for measuring current without breaking the circuit; comes with replacement test leads.

Pocket-sized tester that beeps and lights up near live voltage, the first check before touching any wire.

High-leverage side cutters for cutting and twisting copper and aluminum wire; the standard electrician's plier.

Plier-style stripper that cuts and strips 10-22 AWG wire in one motion, cheap enough to keep a spare in every bag.

Self-adjusting jaws handle Romex 12/2 and 14/3 as well as solid and stranded wire without dialing in a gauge first.

Crimps insulated and non-insulated terminals for 10-22 AWG connectors, with a built-in cutter.

One handle covers Phillips, slotted, Torx, square bits, and three nut driver sizes, cutting down what you carry.

Steel fish tape for pulling wire through conduit and walls on longer runs.

Simple canvas pouch with a heavy-duty brass zipper, sized for hand tools and small meters.

Plugs into a standard 3-wire receptacle and reads wiring faults and GFCI trip on an LCD instead of a row of tiny lights.

1000V VDE-rated insulation for working near live circuits, which a standard hardware-store screwdriver isn't rated for.

Cuts armored and MC/BX cable up to 3/8-inch cleanly, which side cutters chew through rather than cut.

Traces a single wire or cable through a wall or bundle by tone, for low-voltage and data runs.

Plugs a transmitter into an outlet and scans the panel with a receiver to find the right breaker without flipping half the box.

Semi-rigid glow rods for running wire through attics, drop ceilings, and wall cavities where a steel fish tape can't be pushed through open space.

Prints heat-shrink and vinyl labels for panels and circuits, with a symbol library built for electrical work instead of a home-office labeler.

Hinged gel pads with quick-release clips for crawlspace and floor-box work, without the ankle strain of a rigid pad.

Padded belt and pouch combo for carrying hand tools on the body instead of digging through a bag on every trip up a ladder.

Tool-free lever splices for solid and stranded conductors that install and pull apart faster than twisting on a wire nut.

Deburrs 1/2-1-inch EMT ends and drives conduit-body screws in one kit, cheaper than a dedicated bender for shops that mostly bend with a pre-fab or rent one.

Sets a calibrated 5-40 in-lb torque for panel lugs and terminal screws, so connections meet spec instead of being snugged by feel — under-torquing risks a loose lug, over-torquing can crack a terminal.

Non-conductive fiberglass rails instead of aluminum, the standard for any ladder work done near live panels or overhead conductors.

Hands-free light for attics, crawlspaces, and panels with the cover off, where a flashlight means holding it in your teeth or setting it down out of reach.

Wall or ceiling-mounted reel keeps a 50-foot cord off the floor between uses instead of coiling and uncoiling a loose cord every job.

Strips MTW/THHN/THWN-2 insulation on service-entrance and feeder cable without nicking the conductor, a size range the shop's standard Romex strippers don't cover.

Confirms 3-phase sequence and motor rotation direction before energizing equipment, catching a miswired phase that would run a motor or pump backward.

ASTM-compliant Class 0 rubber gloves rated to 1,000V AC, required protection for any live or potentially live work that non-insulated gloves can't provide.

Cast-iron bender head with benchmark symbols and degree/multiplier scales for accurate offsets and saddle bends on 1-inch EMT; pairs with Klein's 51428 handle (sold separately) for a full bender.

Wax-based lubricant that cuts friction on long conduit pulls, the difference between a smooth pull and a stuck run on anything longer than a few feet.

Compact brushless driver for box screws, panel covers, and self-tapping fasteners; 1,825 in-lb of torque with battery and charger included.

Non-contact laser thermometer for spot-checking breakers, lugs, and motor housings for hot spots before they become a failure, without opening an energized panel to touch anything.

Drills and chisels concrete or block for conduit runs and anchors without dragging a cord or compressor to the spot.

Actually trips and verifies AFCI/GFCI protection instead of just confirming wiring, which most residential final inspections require.

Cuts joists, studs, and old boxes open for cable runs and demo, a different job than the impact driver already covers.

Mechanical-advantage come-along for long or heavy pulls that fish tape alone can't handle.

Scans a whole panel, motor, or duct run for hot spots at a glance, catching a failing connection a spot infrared thermometer would miss unless aimed at exactly the right point.

3-speed hammer drill/driver for anchors and masonry boxes, a lighter everyday tool than the SDS rotary hammer for jobs that don't need full chiseling power.

Reusable magnetic directory with number stickers, faster and neater than handwriting a circuit list on the panel door.

Compact drill/driver with two batteries and a charger, a solid do-everything drill for a maintenance cart.

Anti-fog, anti-scratch coating and side shields for basic eye protection cheap enough to keep several pairs around.

One-hand jaw adjustment on fittings and nuts of varying sizes, a standard in any plumbing bag.

Wide, rigid blade holds a straight line further out than a standard tape, and the 2-pack means a spare when one walks off.